1/2" x 300ft PEX Tubing with Oxygen Barrier

1/2" x 300ft Oxygen Barrier PEX Tubing

Everhot

Brand: Everhot

Mfr Part#: BPR1230

Availability: In Stock
Usually ships: Today, if ordered by 3pm
Qty Price
x1
$78.95 / each & Free Shipping
x4 $303.80 / skid & Free Shipping
(4 x $75.95 / each)
  • Description
  • Literature
  • Reviews (13)
  • FAQs (6)

300ft roll of 1/2" PEX Tubing with Oxygen Barrier for use in radiant heating applications.

Meets/exceeds ASTM F876/877, CSA B137.5, DIN 4726 standards.

Certified for use in radiant floor heating applications. UPC listed by IAPMO.

PPI pressure rated at: 79psi @ 200F, 100psi @ 180F, 160psi @ 73F

Packing: Box, 23" x 23" x 10". Weight: 21.0 lbs;

 

 

Everhot PEX Tubing with Oxygen Barrier:

  • Is manufactured to ASTM F876/F877 & CSA B137.5 standards.
  • Tested and Certified by NSF for use in floor radiant heating applications.
  • NSF Certified to the Uniform Plumbing Code.

 

Applications:

1/2" PEX Tubing with Oxygen Barrier can be used for the following radiant heating applications:

 

1. Structural Concrete Slabs (Rebar or wire mesh reinforced, 4-6" thick). Slab-On-Grade Systems (garages, warehouses), Slab-Below-Grade Systems (basements). 1/2" PEX Tubing is secured on top of the reinforcement with wire ties, zip ties or clips.

 

2. Non-Structural Concrete Slabs (Non-reinforced, 1.25"-2" thick). Gypsum or other thermal mass systems over subfloor. 1/2" PEX Tubing is secured to the subloor (i.e. plywood) with plastic clips, pipe clamps or other approved fastening method.

 

3. Below-Subfloor (Staple-up) and Above-Subfloor ("Sandwich") Systems with and without aluminum heat transfer plates.

 

4. Sleeper-type systems (above subfloor) with and without heat transfer plates.

 

5. Engineered Subfloors and Modular Board Systems. 1/2" PEX Tubing is secured by into grooved channels of the plywood or foam board subfloor panels.

 

6. Copper tube finned baseboard radiators.

 

Compatibility:

Everhot Oxygen Barrier PEX Tubing can be installed using either Crimp type connection system (Crimp Tool, Crimp-style PEX Fittings and Copper Crimp Rings) or Clamp/Cinch type connection system (Clamp Tool, Crimp-style PEX Fittings and Stainless Steel Clamps). Also compatible with Push-Fit connection system (such as SharkBite), Viega Press type system and Compression type PEX fittings.

 

This product is a replacement for:

Watts (RadiantPEX): PB032081-300

Viega (ViegaPEX): 11425

Zurn (ZurnPEX): QHR3PC300FX

PEX Tubing colors and packaging may vary by manufacturer.

 

1/2" PEX Tubing with Oxygen Barrier is the most popular size for all radiant floor heating applications due to it's flexibility, light weight and ability to deliver large amounts of heat. According to RPA Standard Guidelines, recommended circuit length for 1/2" PEX tubing is 250-350ft, depending on the application and type of installation.

For snow melt applications, use larger PEX tubing sizes, such as 5/8" and 3/4".

1/2" x 300ft Oxygen Barrier PEX Tubing has an average 4.7 out of 5 rating based on 13 user reviews.
 
Good product
By Verified Buyer on 9/24/2016
Why let the local plumbing store order this when you can order it, free shipping, and a 1/2 the price? I am sure it arrives at my home quicker than ordering it from the local store.
Was this review helpful?  Yes / No
 
Good stuff
By Jr (from Minnesota) on 8/23/2016
I just got pex laid down and covered with concrete. Laid down good and survived the pour. Seems to be well made pex pipe. Hooked up a temporary manifold and pressurized before and during concrete pour, which I would strongly advise. If there is any leaks it will so up right away.
Was this review helpful?  Yes / No
 
Awesome!! Product!!!
By Nate (from Zanesville, Ohio) on 8/6/2016
We bought 3 1000ft rolls and 1 300ft roll. We ordered on a Thursday and it arrived the following Monday right to the door!!! Great product!! Fast shipping!! We have already recommended to others!!!!
Was this review helpful?  Yes / No
 
Haven't used it yet, very fat delivery
By Farmer (from Oh) on 10/15/2015
Hope to use it soon
Was this review helpful?  Yes / No
 
Very professional and item arrived as planed.
By Carlos P (from Stamford CT) on 12/6/2013
The PEX radiant tuning arrived like they said. The price was less expensive then others out there and the warranty is the same as the most expensive out there. Ram all the PEX and will definitely order again from them.
Was this review helpful?  Yes / No
 
Great product, great price!
By tllong (from PA, US) on 11/12/2012
I checked the local stores & PEX Universe had it for half the price they offered & available in more lengths. The product is as easy as it can be to work with for something that's spent it's life coiled up in a box. The length markings printed on the outside are nice to have & the tubing can be written on with a permanent marker for identification.
Was this review helpful?  Yes / No
 
Good product , better price
By Lee Tripp (from Corry, PA) on 9/19/2012
Tubing was easy to form the loops during installation in a 30' x 40" on grade slab.
Was this review helpful?  Yes / No
 
Works great
By Heavyhaul (from Roaring Spring,PA) on 1/18/2012
Can't give five stars because it is the only name brand of pex that I have used. 3/4 and half inch both marked every 10 ft, I believe. I put appox 1400 feet in wood using aluminum plates. I also did 1400 feet in concrete by stapling it to 28 lb foam insulation using the staple gun that I bought from here. Love it.
Was this review helpful?  Yes / No
 
I love Everhot pex tubing
By Bob Hart (from Harrisburg, PA) on 12/21/2011
1/2 inch was easy to work with. I have used both 3/4 and 1/2 inch. My wife just loves the warm bathroom floors on these colder mornings.
Was this review helpful?  Yes / No
 
Good heating tube,
By Bob the builder (from Eastern Canada) on 11/25/2011
Easily workable. Bends in short radius. Quite sturdy. My only complaint is that it is quite stiff below 60F. (It was 55F when we did the install and we kinked it a couple of times) But just bring a heat gun and everything is fine.
Was this review helpful?  Yes / No
 
a good way to buy pex tubing
By I'm not Ralph (from Santa Fe NM) on 11/2/2011
for radiant heat in the floor. So far it seems good but the real test will be later after I have the system installed in entirety
Was this review helpful?  Yes / No
 
Good price
By Radiant Newbie (from Plymouth, MI) on 6/27/2011
"I bought 9 rolls for a basement slab. It seems to be okay. I installed everything and it tested to 100 PSI overnight. The price is great, I sure hope it lasts my lifetime. The description didn't say, but mine had length markings. I was using a full coil per loop, so I didn't check all rolls."
Was this review helpful?  Yes / No
 
I would buy this product again.
By FREDC. (from Long Island NY) on 4/16/2011
In floor thin slab. Product went down pretty well. Bends of 7" to 8" radius OK. No leaks.
Was this review helpful?  Yes / No
Indicate an email address where you wish to receive the answer to your question.
Image CAPTCHA
Enter numbers shown above without spaces. This step helps us to prevent automatic submissions.
Can Oxygen Barrier Pex be used in an open radiant system?
Read 1 answer
Only if it's non-potable. Only Everhot non-barrier PEX is approved for potable water applications. Moreover, there's no need to use oxygen barrier pipe in an open type system since it will have a constant supply of oxygen rich water, rendering the oxygen barrier useless.
Answered on 11/5/2015 by PexUniverse Customer Service
Was this answer helpful?  Yes / No
How much 1/2 pex will I need for a 200sq ft room?
Read 1 answer
0 of 1 people found this answer helpful.
The short answer is that a 300ft roll is sufficient to cover the space and should leave at least a few dozen feet. The detailed answer is that length is determined by the spacing of PEX tubing OC (On Center): For 12" spacing: multiply x1.00 For 10" spacing: multiply x1.17 For 9" spacing: multiply x1.25 For 8" spacing: multiply x1.34 Always remember to add the length needed to connect both supply and return lines to the system/manifold.
Answered on 8/31/2015 by PexUniverse Customer Service
Was this answer helpful?  Yes / No
Can the O2 pex be ran in the ground 25' to connect to the water heater?
Read 1 answer
Yes, given that the pipe is properly protected from freezing temperatures (insulated if needed), abrasives (rocks, pieces of metal, etc.) and rodents where applicable.
Answered on 6/10/2015 by PexUniverse Customer Service
Was this answer helpful?  Yes / No
Can this be piped directly off the boiler?
Read 1 answer
The pipe is rated for up to 180F water at pressures not exceeding 100 psi.
Answered on 3/18/2015 by PexUniverse Customer Service
Was this answer helpful?  Yes / No
what type of tubing is this A,B, C ?
Read 1 answer
1 of 1 people found this answer helpful.
This is type B PEX tubing.
Answered on 2/18/2013 by PexUniverse Customer Service
Was this answer helpful?  Yes / No
How much 1/2" pex tubing is used to make a 180 degree bend when the tubing is spaced 1 foot a part. Thank you
Read 1 answer
The bend only part is about 18-19".
Answered on 6/5/2012 by PexUniverse Customer Service
Was this answer helpful?  Yes / No
The following was added to your shopping cart: ×
X

Forgot Your Password?


Enter your e-mail address below.
You will receive an e-mail
with password reset instructions.

X

Estimate Delivery Date & Cost


Ship to Zip Code:
Qty (Optional):